|
A division of Ashcroft Inc., Weksler has set
the standard worldwide for accuracy, quality and dependability.
Weksler manufactures an extensive line of pressure gauges.
Considerations in Selecting a Weksler
Pressure Gauge
RANGE - The maximum operating pressure should not exceed 75% of the
full-scale range. The normal operating range should be in the middle
half of the range (between 25% and 75% of the full-scale range); whenever possible.
DIAL SIZE - Select a dial size that allows you to comfortably read the dial
from the normal distance when installed.
PRESSURE SYSTEM MATERIAL
- The media to which the gauge will be subjected is critical to the
selection of the proper material for the bourdon tube, bellows, and
socket. Consult “corrosion chart” on Page 5 for proper selection of pressure system materials. Weksler offers
various models with:
-
Phosphor bronze bourdons (or bellows) with brass sockets.
-
316 stainless steel bourdons (or bellows) with 316 stainless
steel sockets.
-
316 stainless steel bourdons with alloy steel sockets.
-
Monel bourdons with monel sockets..
For applications where the above materials may not be suitable, a
diaphragm seal will be necessary to protect the pressure gauge
system.
ACCURACY - Select a gauge having the desired accuracy as follows:
-
1⁄4% – test gauges only (not for in-line service)
-
1⁄2% – Weksler “Royal” gauges (41⁄2˝ dial size and larger)
-
1% – Weksler “Regal” gauges, 31⁄2 “Royal Gauges, 100 MM Gauge,
“EA14” gauge
-
2-1-2% – Weksler Duplex, Differential and Low Pressure Gauges
-
3-2-3% – Weksler BY12, BY42, BK72, UA15, UA20, UA25, UA35 series
utility gauges
MOVEMENT - Select either a gauge with 300 series stainless steel movement
for long wear (Weksler “Royal” gauges, 100 mm gauges, and BY42
series gauges); or a gauge with bronze or brass movement for applications where vibration and pulsation are not
present (all other Weksler gauges).
CASE - Weksler offers a wide variety of
case styles and materials. Determine how the gauge is to be mounted:
direct, surface (wall) or flush (in panel). Determine the desired
case materials: polyproylene (or phenol); aluminum (black enameled) or stainless
steel (300 series). Determine case type: Safety (solid front with blow-out back) Standard (open front with rubber blow-out disc at rear) Note – All
Weksler safety case styles are designated by a number. Standard
Weksler case styles are designated by a letter.
WINDOW - A glass face is standard in most
Weksler gauges. If breakage is a
concern, a plastic or shatterproof glass face is optional at extra
cost on most Weksler “Royal” and “Regal” gauges. (Glycerine filled and sanitary
Weksler gauges have plastic face as standard).
POINTER - All Weksler gauges (except utility types) have adjustable
pointers. This permits pointer repositioning during calibration
check or allows maximum precision at a specific point.
TEMPERATURE - The ambient temperature to which the gauge will be subjected
should not exceed 150°F. If higher temperatures are encountered the
gauge must be isolated from the source of heat. The temperature of the media to which the gauge is subjected to
is also critical. Weksler gauges with phosphor bronze bourdons should not be
subjected to process temperatures in excess of 150°F. Weksler gauges with metal cases and either 316 stainless steel or monel bourdons can withstand higher process temperatures, but as
temperature exceeds 150°F hardening of the gasketing and discoloration of the dial may occur. In addition,
accuracy will be affected by approximately 1.5% per 100°F. Both 316
stainless steel and monel Weksler gauges in metal cases will withstand 750°F for short periods of time without rupture,
but other parts of the gauge will be destroyed and calibration will
be lost.
VIBRATION - If present, a glycerine filled
Weksler gauge is recommended.
PULSATION - If present, a pressure snubber or throttle screw is recommended.
To start, please select a basic type of
Weksler gauge
or contact us for help: |
